How to Replace the Polar H10 Heart Rate Monitor Battery
To replace the Polar H10 heart rate monitor battery, open the sensor cover, remove the old battery, and install a new CR2025 coin cell with the positive side facing up. Check the seal and close the cover securely before pairing the sensor again.
On this page (6 sections)
To replace the Polar H10 heart rate monitor battery, fit a new CR2025 coin cell with its positive side facing up, then close the sensor cover securely. Work over a clear surface, avoid damaging the cover or seal, and follow Polar's instructions for your sensor.
A battery change can restore a sensor that has stopped connecting, but first check that the battery is the cause. The H10 uses a replaceable coin cell, and the sensor needs a sound cover and clean contacts to work as intended.
What battery does the Polar H10 heart rate monitor use?
The Polar H10 uses a CR2025 coin cell battery. Use that battery type when replacing the cell, and check Polar's product instructions for any model or regional differences.
Don't substitute a thicker coin cell just because it fits the opening. The cover needs to close correctly, and a wrong size can put pressure on the sensor or seal.
Keep coin cells out of reach of children and pets. Dispose of the old cell through a local battery recycling option where available.
How do you replace the Polar H10 battery?
Open the battery cover, remove the old CR2025, install the new one positive side up, and reseal the sensor. Keep the battery and sensor dry, and use a small tool only as Polar directs.
- Detach the sensor from the chest strap.
- Turn the sensor over and locate the battery cover.
- Open the cover carefully, following the marking or instructions for the sensor.
- Remove the old coin cell without bending or scratching the contacts.
- Insert a fresh CR2025 with the positive (+) side facing up.
- Check that the seal is in place and undamaged.
- Close the cover until it sits evenly and securely.
Don't force the cover if it resists. Recheck the battery orientation and seal, then consult Polar's instructions rather than prying harder.
What should you check before closing the cover?
Make sure the battery lies flat and the seal is clean, present, and undamaged. Dirt or a pinched seal can keep the cover from closing correctly.
Use a clean, dry work surface. Avoid touching the battery contacts with wet hands, and don't use a sharp metal tool that could scratch the sensor.
How can you check that the new battery works?
Reattach the sensor to the strap and try connecting it through your training app. Follow the app's pairing steps and wear the strap as directed.
If it doesn't connect, remove the sensor from the strap and check the battery's position and the cover. Reinstall the battery once, making sure the positive side faces up and the seal stays seated.
A damp electrode area can help a chest strap make contact during exercise. Keep the sensor itself dry, and check the Polar H10 heart rate monitor review for more about the sensor's features and use.
Could the strap or app be the problem?
Yes. A connection issue can come from the strap, app, or pairing process rather than the battery.
Check that the sensor is attached correctly and follow the app's device pairing instructions.
If you use another chest strap, its pairing steps may differ. Our guide to why a Suunto heart rate monitor is not working covers basic checks that can also help you think through a sensor connection problem.
How can you avoid damaging the Polar H10?
Use the correct coin cell, handle the seal gently, and don't force the cover. The seal helps protect the battery compartment, so replace it or seek service if it appears torn or misshapen.
Remove the sensor from the strap after exercise and keep it dry during battery replacement. Avoid soaking the sensor or leaving moisture inside the compartment.
For a different chest strap with a replaceable CR2032 battery, the COOSPO H6 offers a separate option for training setups that support Bluetooth or ANT+.

A chest strap with a changeable CR2032 battery for compatible Bluetooth or ANT+ training setups.
See it on AmazonThe H6 is a separate heart rate sensor, not a Polar H10 battery replacement. If you'd rather compare simpler setup options, see our best easy-to-use heart rate monitors.
What if the Polar H10 still does not work?
If a fresh CR2025 is installed correctly and the sensor still will not connect, check Polar's troubleshooting instructions or contact Polar support. Don't keep opening the compartment if the cover, seal, or contacts look damaged.
You can also confirm that your phone or receiver supports the connection method you use and that the sensor isn't already paired in a way that blocks a new connection. For other heart rate monitor choices at a lower cost, compare our best budget heart rate monitor options.
An armband uses a different design and charging setup, so it isn't a substitute battery for the H10. The COOSPO armband is rechargeable and may suit a reader who prefers not to replace a coin cell.

A rechargeable armband option for workouts when you want to avoid replacing a chest sensor coin cell.
See it on AmazonFor oxygen and pulse readings rather than chest strap heart rate tracking, the Zacurate fingertip oximeter includes two AAA batteries and a user-facing LED display.

A fingertip device for checking SpO2 and pulse rate, powered by two included AAA batteries.
See it on AmazonWhat is the safest way to finish a Polar H10 battery change?
Use a CR2025, keep its positive side facing up, and close the sensor only after checking the seal. If the cover won't sit evenly or the sensor still fails after a careful battery change, pause and use Polar's support guidance.
For regular workouts, detach the sensor from the strap after use and store it according to Polar's instructions. If you want a broader comparison before choosing a replacement monitor, review our heart rate monitor options and select a model that fits your preferred strap and connection setup.
Frequently asked questions
What battery does the Polar H10 use?
The Polar H10 uses a CR2025 coin cell battery. Check the sensor's instructions before replacing it, and use a new battery of the same type.
Keep coin cells away from children, and dispose of the old battery according to local rules.
Which way does the battery go in a Polar H10?
Place the CR2025 battery with its positive side facing up, as shown in Polar's replacement instructions. Avoid touching both sides of the coin cell at once with a metal tool, and make sure it sits flat before closing the sensor cover.
Why won't my Polar H10 connect after a battery change?
Check that the battery is fresh, seated with the positive side up, and that the sensor cover is closed properly. Remove and reinstall the sensor battery if needed, then pair it again in your training app.
Also confirm the sensor contacts and strap are clean and dry.
How often should I replace the Polar H10 battery?
Replace the battery when the sensor no longer connects or reports low power, rather than on a fixed schedule. Battery life varies with use and storage.
Remove the sensor from the strap after exercise and store it as Polar recommends to help reduce unnecessary battery drain.
About this guide: Our look at replacing a Polar H10 heart rate sensor battery draws on maker specs, materials and what owners report. See how we research.



